Skip to content
Back to search results

ATR-FTIR

Introduced by
Joop Fahrenfort
Year
1961
Type
Vibrational spectroscopy technique
Family
Infrared Spectroscopy
Font size

What does it do?

Attenuated Total Reflectance (ATR) Fourier Transform Infrared (FTIR) spectroscopy is a variant of conventional FTIR that measures infrared absorption through evanescent-wave interrogation of samples in direct contact with a high-refractive-index crystal. Developed by Harrick and Fahrenfort in the 1960s, ATR-FTIR is now the dominant form of FTIR spectroscopy, enabling rapid, non-destructive characterization of organic compounds, polymers, coatings, and biological materials without extensive sample preparation.

The intuition behind the method

When infrared light hits a transparent crystal (like diamond or germanium) at a steep angle from within the crystal, it undergoes total internal reflection at the crystal-sample interface. At this interface, an evanescent wave penetrates into the sample to a depth of only a few micrometers. The sample absorbs infrared radiation at frequencies matching its vibrational modes; the attenuated reflected light is then analyzed. Since the sampling depth is very shallow, ATR is ideal for surface analysis and avoids transmission path-length issues that plague conventional FTIR.

History

Harrick developed the theory of attenuated total reflectance in 1960 and published the first practical ATR technique. Fahrenfort independently developed and demonstrated practical ATR in 1961. For decades, ATR remained a specialized technique because it required alignment and frequent cleaning. The revolution came in the 1980s-1990s when Fourier transform optics replaced grating spectrometers and motorized ATR accessories became reliable. Today, ATR is the standard sampling method for most FTIR instruments.

When to use it

Apply ATR-FTIR to characterize solid, liquid, and paste samples rapidly: polymers, coatings, minerals, pharmaceutical tablets, food components, and biological tissues. ATR is ideal when samples are opaque or too thick for transmission FTIR, or when minimal sample preparation is desired. Assumes good contact between sample and crystal and that the sample refractive index is lower than the crystal.

Limitations and considerations

  • Quantitative interpretation difficult: peak intensity depends on sample contact, refractive index, and geometry
  • Refractive index effects: spectra differ from conventional transmission FTIR; library matching may fail
  • Crystal surface degradation: hard samples scratch diamond or sapphire crystals; replacement is expensive
  • Spectral distortion from high absorbing samples: baseline artifacts and band distortion occur for strong absorbers

Source conditions do not replace independent scientific review or validation by an analysis engine.

Strengths

  • Minimal sample preparation: solids, powders, liquids, and pastes analyzed directly
  • Fast analysis: spectra acquired in seconds
  • Surface-sensitive: probes only the top 1-10 micrometers, useful for coating and surface analysis
  • Non-destructive: samples recovered unmodified after analysis

Applications

  • Quality control in polymer and coating manufacturing: rapidly identifying contamination, cross-linking, or degradation via spectral comparison to standards
  • Pharmaceutical tablet and excipient analysis: detecting polymorphic forms and identifying active pharmaceutical ingredients and binders
  • Forensic analysis: matching fibers, paints, and plastics from crime scenes to suspect materials via spectral comparison
  • Biomedical diagnostics: analyzing skin, tissue, or bodily fluids for disease biomarkers via spectroscopic patterns

How it works

How it works

1

Infrared light is directed into a transparent crystal (ATR element) at a shallow angle, creating internal reflection.

2

An evanescent wave extends into the sample placed on the crystal surface; infrared radiation interacts with the sample over a penetration depth of 1-10 micrometers.

3

Sample molecules absorb infrared photons at characteristic wavenumbers corresponding to molecular vibrations.

4

The attenuated reflected beam is collected and guided to an FTIR interferometer for Fourier transformation.

5

The resulting spectrum plots absorbance or percent reflectance versus wavenumber; peaks identify functional groups and molecular structure.

Common pitfalls

  • Comparing ATR spectra directly to transmission FTIR library spectra; spectral patterns can differ significantly due to refractive index effects
  • Poor sample contact leading to weak or noisy spectra; apply even pressure and clean the crystal between samples
  • Assuming uniform penetration depth; penetration depth varies with wavenumber and sample refractive index

Frequently asked questions

What materials are used for ATR crystals?

Common materials include diamond (hardest, most durable, most expensive), sapphire, germanium, and zinc selenide. Diamond is preferred for hard samples; germanium for aqueous solutions (higher refractive index, shorter penetration); zinc selenide for biological and organic samples. Choice depends on sample type and cost considerations.

Why do ATR spectra sometimes look different from transmission FTIR spectra of the same material?

ATR spectra are distorted by the optical properties of the sample (refractive index, absorption) and the ATR geometry. High-absorbing bands appear distorted; peak ratios change compared to transmission. This is why ATR spectra cannot always be directly matched to transmission FTIR libraries without correction factors.

How deep does ATR probe into the sample?

The penetration depth (distance where intensity falls to 1/e) typically ranges from 1 to 10 micrometers and depends on wavenumber, incident angle, and sample refractive index. Higher wavenumbers and steeper angles give shallower penetration. This makes ATR surface-sensitive, ideal for coatings and thin films.

Related methods

Sources

  1. Harrick, N. J. (1960). Study of physics of internal reflection from metals. Journal of Physics and Chemistry of Solids, 13(2), 143-155.

    Open publication reference
    Copied.
  2. Fahrenfort, J. (1961). Attenuated total reflection: a new principle for the production of useful infra-red reflection spectra of organic compounds. Spectrochimica Acta, 17(6), 698-709.

    Open DOI reference
    Copied.
  3. Humecki, H. J. (Ed.). (1995). Practical Guide to Infrared Microspectroscopy. CRC Press.

    Open publication reference
    Copied.